Description
MAGNACRYL PRESTIGE VELOR is an insulating wall paint with a velvety aspect and high scrub resistance. Non-glossy, 100% acrylic, solvent-free*.
FEATURES – USE
• An insulating wall paint. It prevents the bleeding of water-soluble stains such as nicotine, ink, dried moisture rings, etc.
• Can isolate/ block plasticizers .
• Serves simultaneously as a primer and as a finish ( one-pot system ) and gives a smooth end result ( good flow ).
• A velvety paint that does not shine . Has a high decorative value and can be ideally applied to walls in premises subject to intensive load/passage.
• Is a non-porous paint that can be applied on a wide variety of surfaces such as plaster, concrete, primed substrates, fiberglass, etc.
• Extends through its non-porous nature of the open time of the next layer.
• A low- tension paint that can be applied to old ones without the risk of detachment due to voltage differences layers of paint.
• The risk of cracking on acrylic sealant is very small, given its flexibility.
• Is very scrub-resistant after complete drying ( class 1 according to DIN EN 13300) and resistant to most water-based disinfectants. Can therefore also be used for sanitary rooms, bathrooms, …
• Is water and grease repellent (also called “hydrophobic” and “lipophobic”) and therefore has an extremely low adhesion of dust. Beading effect → Water drops will bead off. Excellent stain resistance .
• IAQ or indoor air quality emissions: class A+ and solvent-free*: VOC < 1 g/l
• Can also be used in areas where food is prepared, treated and processed in accordance with HACCP
principles or REGULATION (EC) No 852/2004 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL on the hygiene of foodstuffs
• Water vapor permeable
• Unsaponifiable
SUBSTRATES AND PAINT SYSTEMS
MAGNACRYL PRESTIGE VELOURS can be applied indoors on dry, coherent and clean substrates.
Substrate pre-treatment
New surfaces
• Remove parts and dust that do not adhere or do not adhere well by brushing or cleaning.
• Apply a first coat of MAGNACRYL PRESTIGE VELOUR , diluted with 5 to 10% water or a coat of MAGNAPRIM FIX or Apply MAGNAPRIM , if necessary diluted with 5 to 10% water.
Pre-painted surfaces in good condition
• Clean, degloss old glossy paint layers and clean if necessary using POLYFIILA PRO S600 .
Previously painted surfaces in poor condition:
• Remove non-adherent parts, open cracks and repair with POLYFILLA PRO X100 .
• Prime the repaired areas with a first coat of MAGNACRYL PRESTIGE VELOR diluted with 5 to 10% water or a coat of
MAGNAPRIM FIX or MAGNAPRIM , optionally diluted with 5 to 10% water.
• Apply 1 coat of MAGNACRYL PRESTIGE VELOUR , diluted with 5 to
10% water or a layer of MAGNAPRIM FIX or MAGNAPRIM possibly diluted with 5 to 10% water.
Finish
• Apply 1 or 2 coats of MAGNACRYL PRESTIGE VELOR undiluted until full coverage.
Comments
1. Substrates with water-soluble components (nicotine stains, ink, …): It is necessary to apply 2 undiluted layers with a minimum interval of 24 hours to avoid blood flow. You can also work with
DIALPRIM as an insulating base layer.
2. To obtain a nice decorative aspect: please respect the yield of ± 10 m 2 /L + a fur roll with
TECHNICAL NOTE
* raw materials used may still contain traces of VOC, hence VOC < 1 g/L
hair length (pile height) of ± 12 mm can be used
PROCESSING THE PRODUCT
Drying time at 20°C and 60% RH
• Dust dry 1 hour
• Dry 1 hour
• Paintable 6 hours
24 hours, if contaminated with water-soluble stains
Processing conditions
• Substrate Temperature min. 10°C
• Ambient temperature min. 10°C – Max. 30°C
• Relative humidity Max. 80%
Processing and dilution
• Brush and roll ready to use. If necessary, dilute up to 3% with water.
• Syringe Please consult us. Can be sprayed with HEA tip (Wagner) or FF LP tip(Graco) – opening: 0.017 inch
Cleaning material
Water, preferably immediately after use
COMPOUND
• Binder(s): 100 % Acrylate solvent free
• Pigment(s): Titanium dioxide and stable mineral fillers
• Solvent: Water
• Dry matter content: By weight: 58 ± 2% By volume: 43 ± 2%
• VOC-EU limit value: EU limit value for this product (cat A/a): 30 g/l (2010). This product contains max. 1 g/l VOC.
TECHNICAL FEATURES
• Aspect: Velvety (6-9 GU at 60° and 6-10 GU at 85°)
• Colour: White + 2 Bases: AW and AC
• Colorize: Via the Trimetal ACOMIX color mixing machine
• Packaging: 1L – 2.5L – 5L – 10L
• Density at 20°C: 1.35 ± 0.05
• Theoretical return: ± 10 m²/l/layer (depending on the suction power and roughness of the substrate)
• Din EN 13300
• wet wear resistance : class 1
• hiding power : class 2
• gloss level : matt ( 6-10 GU@85°)
• grain size : fine ≤ 100µ
• Indoor air climate emissions
• A+ (gradation ranging from A+(very weak emission) to C(strong emission))
STORAGE – SHELF LIFE
Store preferably frost-free and protected in the original and unopened packaging, at a temperature between 5°C and 35°C.
At least 24 months shelf life under stated conditions
HYGIENE AND SAFETY
Consult our product safety data sheet. If you do not have it, it will be sent to you on request.
Keep out of reach of children.
Reviews
There are no reviews yet.