Carboline Plasite 4550 S – Solvent Free Epoxy Novalac – Lining

“This linings selection tool is for guidance only. Final lining recommendation has to be approved by the manufacturer. Manufacturer terms & conditions apply”

Novalac Epoxy

High impact and thermal shock resistance
Superior adhesion to steel and concrete
Resistance to a broad range of chemicals
Can be applied up to 60 mils in one coat
Can be sprayed using single component airless equipment
Passes ASTM G210 - Severe Waste Water Analysis Test (SWAT)

Choose Packaging

Pick Color

Light Grey

Clear

Description

PLASITE 4550 S is a 100% solids, flake filled, premium novolac epoxy coating designed for internal steel and concrete substrates. It is a two component system consisting of four-parts by volume of Part A resin and one part by volume of Part B hardener. It is applied by plural component or single component spray equipment, from a total thickness of 20-60 mils (500-1500 microns) in a single coat application for a variety of applications. This product has been tested and is approved for crude oil storage and transportation up to 350°F (177°C). It has superior thermal shock resistance over the range -40° to 350°F (-40 to 177°C). Typical Uses: Crude oil tankers, chemical storage tanks, wastewater clarifiers, plating vats, oil storage tanks, catwalks, pulp and paper liquor tanks or concrete exposures in wastewater applications.

Additional information

Choose Packaging	20L, 5L
Pick Color	Light Grey
Linings - Tanks & Equipment	Dearation Columns, Dehydrators, Desalter, Electrostatic Treater, Flare & Compressor KO Drums, Flotation Cells, Main Cooling Water Lines, Produced Water Tanks, Seawater Dearator, Seawater Exchanger, Seawater Filter, Separators, Suction and Fuel Gas Scrubbers
Linings - Process vessels	Crude Oil (Sour), Degassing, Gas Oil Separation, Hydrocarbon Gas System, Produced Water, Seawater System, Slug Catcher, Water Injection System
Pressure	<10 barg, <50 barg, 10 barg ≥ P < 50 barg, 35 Bar (500 psi)
Lining - Tank Storage Cargo	Ammonia 10%, Ammonia 28%, Crude Oil (Sour – High Sulphur), Deionized water up to 50°C, Diesel, Ethanol, Ethylene Glycol, Fatty Acid, Fuel Oil, Fuels (high aromatic), Fuels (low aromatic), Hydrochloric Acid 10%, Hydrochloric Acid 20% 25°C, Oil – Hydraulic / vegetable, Phosphoric Acid 0-10%, Produced Water, Sewage Brown Water, Sodium Hydroxide 0-5%, Sodium Hydroxide 5-10%, Sodium Hydroxide 50%, Sour Water, Sulphur, Sulphuric Acid 0-20%, Toluene, Urea Solution, Water, Xylene
Secondary Containment	Ammonia Solution, 0-5%, Ammonia Solution, 0-5%, Ammonia Solution, 6-20%, Aviation alkylates (C8 paraffins and isoparaffins, BP 95-120°C), Aviation Gasoline, Biodiesel B100, Biodiesel B20, Biodiesel B5, Bioethanol, Boric Acid Solutions, Brake Fluid, Brine, Bunker Fuel, Butanol (all isomers), Crude Oil – Sweet and Sour, High Sulphur, Diesel, Ethanol, Technical, Fuel Oils, Gas Oil, Gasoline, Premium unleaded, Gasoline, Regular unleaded, Jet Fuel, JP4, JP5, JP8 & Jet A, Phosphoric Acid, 0-10%, Phosphoric Acid, pH >3, Potassium Hydroxide, >20%, Potassium Hydroxide, 0-5%, Potassium Hydroxide, 6-20%, Skydrol, Sodium Hydroxide, >20%, Sodium Hydroxide, 0-5%, Sodium Hydroxide, 50%, Sodium Hydroxide, 6-20%, Sodium Hydroxide, 73%, Sodium Hypochlorite, <1%, Urea Solutions, Water, Sewage Treatment, Water, Wastewater, White Oils
Concrete Linings Area	Basin, Sump, Trench, Pit (Interior), Secondary Containment
Concrete Linings End Use	Molten Sulphur
Max operating temp	25°C, 40°C, 50°C, 50°C ≥ T < 90°C, 60°C, 70ºC, 80ºC
Linings - Pipe Internal	Crude Oil (Sour), Crude oil up to 250°F (121°C), Natural Gas (non Sour), Natural Gas (Sour), Sour Water
Steam Out Rating	100°C, 120°C
Coating, Lining or PFP	Lining
Industry	Industrial Coatings
Brand	CARBOLINE
Surf Prep M&R	FR Sa2.5, Solvent Clean SSPC-SP1
Surf Prep New Steel	Sa2.5, Sa3
Surf Prep Concrete	SP13
Substrate	Carbon Steel, Concrete, Primed Steel
Layer	Primer/finish
Product type	Novalac Epoxy

Detailed information about Carboline Plasite 4550 S – Solvent Free Epoxy Novalac – Lining

Intended uses	Fatty Acid, Phosphoric acid 10%, Sulfuric acid conc, Sulfuric acid 10%, Hydrochloric acid 20%, Hydrochloric acid 10%, Ammonia 28%, Ammonia 10%, Sodium Hydroxide 50%, Sodium Hydroxide 10%, Ethanol Toluene, Xylene Gasoline Unleaded, Ethylene Glycol, Crude Sour, Urea solution, Oil hydraulic / vegetable, Brine, Sewage Brown, Water, Water
Volume solids	100%
VOC	As Supplied : 0 gr/lt
Max. DFT	750 µm
Min. DFT	500 µm
Theor m2/lt at average DFT	2 m2/lt
Typical DFT	500 micron DFT
Min. consumption spray m2/lt typical DFT	1.5 m2/lt
Drying time (25C)	12 hrs
Drying time (10C)	30 hrs
Drying time min. temp	30 hrs
Min. application temp.	10°C
Max. operating temp.	Depending on chemical
Chemistry	Novalac Epoxy

Downloads

Product name	Document name	Document type	Language	Download
Carboline Plasite 4550 S – Solvent Free Epoxy Novalac – Lining	Plasite 4550 S PDS	Product Data Sheet	English	Download
Carboline Plasite 4550 S – Solvent Free Epoxy Novalac – Lining	Application Guide Plasite 4550 S	Manual	English	Download
Carboline Plasite 4550 S – Solvent Free Epoxy Novalac – Lining	Brochure Plasite 4550 S	Brochure	English	Download

Reviews

There are no reviews yet.

Be the first to review “Carboline Plasite 4550 S – Solvent Free Epoxy Novalac – Lining”

Carboline Plasite 4550 S – Solvent Free Epoxy Novalac – Lining

Description

Additional information

Detailed information about Carboline Plasite 4550 S – Solvent Free Epoxy Novalac – Lining

Downloads

Reviews

Customer support

Contact EN

PaintDeals.com

Recent posts

About PaintDeals

Carboline Plasite 4550 S – Solvent Free Epoxy Novalac – Lining

Description

Additional information

Detailed information about Carboline Plasite 4550 S – Solvent Free Epoxy Novalac – Lining

Downloads

Reviews

Related products

ISO 12944 Cx Very High – 3 coat – Zinc rich Epoxy Carbozinc 858 + PU Carbothane 134HP

Carboline Carboguard 690 – Moisture Tolerant Epoxy | Pipe Coating

PFP – Pyrocrete 241 – Light Weight Cementitious Fire Proofing

Primer/Finish – Carboguard 890 – 2C Epoxy Mastic