COATING SYSTEM – CARGO TANKS DRY – 1 COMPONENT URETHANE

For use in Dry Cargo Tanks

Moisture Cure Urethane

(1 customer review)

Kleur kiezen
  • Gray
  • Red Gray
Kies verpakking
-
+
Kies verpakking
-
+

Description

Application Procedure

Surface Preparation

  1. Clean the surface from contaminents such as oil, grease, salts & chlorides using a biodegradable degreaser such as Safeclean BIO 3, followed by a rinse with clean water
  2. Remove any loose rust, paint and corrosion by abrasive blasting, UHP waterjetting or power tool cleaning.

Paint Application

Apply by brush, roller or spray:

Layer Product Name  Generic Type Mix Ratio Min. Temp. Dry time @ 25°C m2/L brush m2/L spray Thinner
1st coat Stelpant PU Zinc 1 comp. zinc rich MCU primer n/a -5°C 0,5 hrs 8,01 5,34 PU-Thinner
2nd coat Stelpant PU Zinc 1 comp. zinc rich MCU primer n/a -5°C 0,5 hrs 8,01 5,34 PU-Thinner

Find the right application tools in the toolbox for solvent based coatings

Tips

  1. Do not apply or expose the paint to above 96% relative humidity, rain or temperatures below -5°C during application or curing for min.30minutes.
  2. Apply a stripe coat by brush on sharp edges, cavities such as pitting corrosion, in corners and difficult areas to reach by spray
  3. Respect to minimum and maximum overcoating time as per product data sheet

 

Always read the product technical data sheet and safety data sheet before using the coatings, to be found in the Download section.

Additional information

Weight 25 kg
Onderdelen

Compatibel met

1 component, 2 component

Substraat

, , ,

Budget - Laag (*) tot Hoog (*****)

****

Productiviteit - Laag (*) tot hoog (*****)

*****

Kwaliteit - Laag (*) tot Hoog (*****)

*****

Surf M&R

, , , , ,

Surf Prep Nieuw Staal

,

UV-bestendigheid - Laag (*) tot hoog (*****)

Eindgebruik

,

Merk

Industrie

Systemen

Coating, lining of PFP

Marktsegment

Oplosmiddel

Laag

Soort product

Detailed information about COATING SYSTEM – CARGO TANKS DRY – 1 COMPONENT URETHANE

Intended usesDry cargo tanks
Volume solids71%
VOCapprox. 255 g/l gr/lt
Max. DFT300 µm
Min. DFT150 µm
Theor m2/lt at average DFT9 m2/lt
Typical DFT200 micr. DFT
Min. consumption brush/roller m2/lt8 m2/lt
Min. consumption spray m2/lt typical DFT5.5 m2/lt
Drying time (25C)0.5 hrs
Drying time (10C)1.5 hrs
Min. application temp.-5°C
Max. operating temp.max. 140°C (dry heat) or 60°C (wet heat)
ChemistryMoisture Cure Urethane

Downloads

Product name Document name Document type Language Download
COATING SYSTEM – CARGO TANKS DRY – 1 COMPONENT URETHANE PDS Stelpant PU-Zinc Product Data Sheet English Download

1 review for COATING SYSTEM – CARGO TANKS DRY – 1 COMPONENT URETHANE

  1. Ernst Huybrechts

    Best performing cargo tank system used in 25 years

Add a review

Your email address will not be published. Required fields are marked *

Need Help?